The xTool P2 desktop CO2 laser, Samcraft's hands-on guide.

xTool P2 CO2 Laser: What I've Learned Since 2023

The xTool links in this post are affiliate links. xTool asked me to make one of the P2 videos this post pulls from, and they've never had a say in what I write. I also sell test files for this machine, and I'll point them out when they come up.

My xTool P2 has been cutting and engraving in my shop since 2023. It's cut and engraved signs, slate coasters, acrylic and a stack of test cards, and I've taken the head apart to clean it more times than I can count. This post is everything I'd tell a friend who's looking at a P2, and what I wish somebody had told me before mine showed up.

One thing to know up front: xTool doesn't sell the P2 new anymore. The xTool P2S took its place, and xTool sells the P2 and P2S as official refurbished units when it has them in stock. There are a lot of P2s out there working every day, and plenty change hands secondhand.

The short version

A desktop CO2 with cameras that let you fix your own mistakes.

Where it shines

Dual cameras for placement, clean CO2 cuts in wood and acrylic, passthrough for long stock, and a big enclosed bed.

Where it fights you

Daily lens and mirror cleaning, a short working height without the riser, and a gantry you should check for square.

Best for

Small shops cutting and engraving wood, acrylic and leather who want camera placement without a pro-size machine.

The xTool P2 at a glance

These are xTool's published numbers from its P2 documentation and the refurbished P2/P2S page.

Specs
Laser 55W CO2 (glass tube)
Working area 600 x 305 mm (23.6 x 12 in)
Bed size 680 x 360 mm (26.7 x 14.1 in)
Max workpiece height 64 mm with tray, 71 mm without, 215 mm with the riser base
Passthrough Material up to 118 in (3,000 mm) long
Cutting 18 mm wood and 20 mm acrylic in one pass
Max speed 600 mm/s
Processing precision 0.01 mm
Cameras Two 16 MP cameras: panoramic plus close-range, autofocus
Rotary 3 to 50 mm diameter without the riser, up to 180 mm with it
Built in 1.4 L water cooling, adjustable air assist (15 to 150 kPa), 145 CFM exhaust fan
Room temperature 10 to 30°C (50 to 86°F). Below 10°C, xTool says to add antifreeze.
Footprint and weight 1000 x 639 x 268 mm, 45 kg
Software xTool Creative Space (now xTool Studio). xTool also lists LightBurn.
Availability Refurbished only, sold in the US with a 6-month warranty

What it does well

Two cameras that let you fix your mistakes

This is the P2's party trick, and I use it all the time. Hit refresh and the panoramic camera takes a photo of the whole bed and flattens out the fisheye distortion. Then "capture close view" moves the head and snaps a 16 MP photo straight down from a camera that rides next to the laser. That close view is the one to trust for alignment. The wide view can look slightly off when the close view is dead on.

To prove it, I made three mistakes on purpose on a sign: left a word out, under-powered the cut and ran the engrave too light. Then I pulled the piece out of the machine, put it back, lined it back up with the close camera and fixed all three. Unless you knew, you couldn't tell which parts were engraved separately. Without a fixture on most other machines, that piece would've been firewood.

Camera tips from my own jobs

  • Enter your material thickness. Measure it with calipers. The software uses it to correct the camera image.
  • Use the close view for alignment. Ctrl + scroll to zoom, Shift + drag to pan, arrow keys to walk the design into place.
  • Square your piece first. I set machinist 1-2-3 blocks against the front edge and pull the piece up against them. It squares the piece to the machine every time.
  • Missed a vector? Run just the missing layer first, then run everything together.

It cuts clean

This is what a CO2 gantry machine is for. The head moves over the work, so cuts come out straight up and down, and the air assist keeps the edges clean. xTool rates it for 18 mm wood and 20 mm acrylic in a single pass. From my own cutting tests, 6 mm plywood cuts at 10 mm/s and 80% power.

Engraving holds its own

I ran the P2 side by side with a 100W Thunder Nova 35 on slate, birch plywood and acrylic, using each maker's default settings. Side by side, they looked pretty comparable. If they came out the same color, I couldn't tell you which machine did which. Judge resolution, not darkness. Does it look like it was drawn with a pencil or a big permanent marker? That tells you the spot size.

Passthrough for long stock

xTool's AutoPassthrough feeds material up to 118 inches long through the machine, so long signs and boards aren't limited to the 600 mm working area.

Drawn to scale Working area 600 x 305 mm Bed 680 x 360 mm (dashed) Passthrough: material up to 3,000 mm long Max height 64 71 215 tray no tray riser millimeters, to scale

Where it fights you

Clean the lens and mirrors every day

That's my advice, anyway. Before you start, or as the last thing before you leave the shop. Dirty optics mean weaker cuts, poorer engraves and wasted material. On the P2, it takes about five minutes once you've done it a couple of times:

  • Power off and slide the gantry slowly by hand.
  • Pull the magnetic covers off the laser head. Two hex screws release the lens module.
  • The mirrors are magnetic. Put them back in the same orientation, notch and all.
  • Clean with 70% isopropyl and foam-tipped swabs, center out. Hold the lens by its edges only.
  • The lens retaining ring only needs to be snug. Don't crank it down.

If you cut a lot of acrylic, clean the nozzle even more often. Acrylic gums it up fast. It's a little lengthy compared to some machines I've had, but it's just something you have to do.

Check your gantry for square

On the P2, the gantry is held square by belt tension. If your machine has been shipped or moved around, cut a 100 mm test square and measure the diagonals, not just the sides. The sides on mine were all within a few tenths of a millimeter, but the diagonals were over a millimeter apart. That's a racked gantry.

The fix: power off, loosen the Y belt tensioners on both sides, pull the gantry square against 1-2-3 blocks set on the front wall, then retighten with equal tension. Realign your mirrors afterward. Contact xTool support first. This is my fix, not an official one. My free 100 mm square test file is what I use to check it.

It's short without the riser

Standard working height is 64 mm with the tray in. Anything taller, including most tumblers on the rotary, needs the riser base, which is sold separately and takes you to 215 mm.

The built-in fan isn't enough by itself

The P2 has an exhaust fan in the case, but for real fume extraction you want an inline duct fan pulling the air out of the building. I run a 6 inch duct fan with blast gates. You don't need a proprietary one.

Software

xTool lists LightBurn as supported. I never got my P2 working with it, so I run it in xTool's own software. Double-check your settings before you hit start, too. I've had the material thickness reset on me after picking a material preset.

What I'd add on day one

  1. An inline duct fan vented outside, with a blast gate.
  2. A cleaning kit: gloves, 70% isopropyl, foam swabs, a microfiber cloth.
  3. Machinist 1-2-3 blocks for squaring work and the gantry.
  4. Digital calipers for material thickness and test squares.
  5. CO2 laser safety glasses rated for 10,600 nm.
  6. A test routine. Dial in your own settings instead of trusting the defaults.
From the Samcraft shop
Samcraft complete engraving and cutting test file kit for xTool software.
Complete Test File Kit for xTool Software

Engraving tests across three speed ranges plus cutting tests, laid out so you can run them once, find your power and speed, and stop guessing. It's where my 6 mm plywood cut settings came from.

Digital download. A LightBurn version is available too.

See the Test File Kit

Should you buy one?

Buy it if

  • You cut and engrave wood, acrylic, leather and slate
  • You want camera placement that lets you rerun and fix jobs
  • You work with long boards and signs that need passthrough
  • You're fine with a refurbished or used machine and its shorter warranty

Think twice if

  • You won't keep up with daily optics cleaning
  • You need to mark bare metal. That's a fiber laser job.
  • Your shop drops below 10°C in winter without heat
  • You'd rather have a new machine with a full warranty. Look at the P2S.

Want the current version? Read my xTool P2S guide, or see how the whole lineup stacks up in xTool CO2 lasers compared.

See the P2S at xTool (affiliate link)

Common questions

Can you still buy the xTool P2 new?

No. The P2S replaced it. xTool sells the P2 and P2S as official refurbished units in the US with a 6-month warranty when it has stock.

How big is the xTool P2's working area?

600 x 305 mm (23.6 x 12 in) inside a 680 x 360 mm bed. Passthrough takes material up to 118 inches long.

How tall an item fits in the P2?

64 mm with the tray, 71 mm without it, and 215 mm with the riser base.

How often should I clean the P2's lens and mirrors?

I clean mine every day before I start. It takes about five minutes once you're used to it. If you cut a lot of acrylic, clean the nozzle often too.

Why is my P2 cutting squares that aren't square?

Measure the diagonals of a test square, not just the sides. If the diagonals differ, the gantry is likely out of square. Contact xTool support first. The fix that worked for me was loosening the Y belts, squaring the gantry against 1-2-3 blocks, retensioning and realigning the mirrors.

Does the xTool P2 work with LightBurn?

xTool lists LightBurn as supported. I never got my P2 working with it, so I use xTool's own software.

What cutting settings work for 6 mm plywood on the P2?

From my own cutting tests, 10 mm/s at 80% power cuts 6 mm plywood on my machine. Run a test on your own sheet, because plywood varies a lot.

More from the Maker Guides

xTool P2S: the current 55W desktop CO2

xTool P3: the 80W flagship

xTool CO2 lasers compared

See my laser files

Watch more of my P2 work on Samcraft on YouTube, including fixing laser mistakes with the P2's cameras, lens and mirror cleaning, gantry alignment and the P2 vs Thunder Nova 35.

Sam

Disclosure: xTool requested one of the P2 videos this post draws on. xTool links in this post are affiliate links that may earn Samcraft a commission at no extra cost to you. xTool has no editorial input or control over Samcraft content. Samcraft sells its own test files for xTool machines, mentioned here. Specifications are from xTool's published documentation. Last reviewed September 2026.

Back to blog