The eufyMake E1 UV printer, Samcraft's hands-on guide.

eufyMake E1 UV Printer: What I've Learned After a Year

eufyMake sent me my first E1 in 2025 in exchange for content, and the eufyMake links in this post are affiliate links. They've never had a say in what I write. I also design and sell accessories for this machine, and I'll point them out when they come up.

I've had a eufyMake E1 on my bench since the fall of 2025. It has printed pens, pet tags, tumblers, magnets of my kids and a whole lot of test cards. This post is everything I'd tell a friend who asked me whether to buy one, and everything I wish somebody had told me the week mine showed up.

The short version

A great printer for one-off prints. It needs help to run batches.

Where it shines

Photo-quality color, raised texture up to 5 mm, an easy app, and a setup a beginner can finish in an evening.

Where it fights you

Repeatable placement, fumes in a closed room, and ink spent keeping the printhead healthy.

Best for

Makers and small shops printing hard goods who are willing to set up a real placement workflow.

The eufyMake E1 at a glance

These are eufyMake's published numbers, plus one line from my own shop where it matters. If you only read one table before you buy, make it this one, because the bed sizes and height limits decide what you can actually sell.

Specs
Standard flatbed print area 330 x 420 mm (13 x 16.5 in)
Mini flatbed print area 330 x 90 mm (13 x 3.54 in)
Mini bed, what I actually get with Zero Point 333 x 88 mm, measured in my shop
Max object height 60 mm standard bed, 80 mm mini bed
Height variation across the print face Within 2 mm
Max load on the bed 1.5 kg (3.3 lb)
Raised texture Up to 5 mm
Resolution 1,440 DPI
Inks CMYK + White + Gloss, individual cartridges
Rotary (with the rotary attachment) 45 to 100 mm diameter, 80 to 245 mm tall, tapers up to 13°
Other print modes UV DTF film with the roll-to-film attachment
Positioning 8 MP camera plus dual lasers for height
Maintenance JetClean automatic self-cleaning
Footprint and weight 590 x 250 x 407 mm, 20 kg (44 lb)
Room temperature 15 to 35°C (59 to 95°F)
Ink safety GREENGUARD Gold (covers the ink emissions only)
Software eufyMake app and eufyMake Studio for PC, 20,000+ templates

What it does well

The prints look great

One of the first things I printed was a ceramic magnet of my two boys, straight from a photo on my phone. It took about five minutes and it looked as good as anything a home photo printer puts out! That's the moment most people fall in love with this machine, and it's a fair reason to.

The raised texture is the other party trick. Brush strokes you can feel, faux leather grain, raised logos. Five millimeters of texture is plenty for most product work.

Setup is easy

From box to first print is about an evening. You load six ink cartridges, slide in the JetClean cleaning cartridge, connect it in the app, update the firmware, and let the initialization run. The app tells you up front that initialization takes around 45 minutes, which I appreciated. Go get a snack!

A few things worth knowing on day one:

  • Wear gloves when you load ink. None come in the box.
  • Check the dates on your ink. The cartridges carry use-by dates in day, month, year order, and the ones in a single kit can be months apart.
  • There's no power switch. The machine is designed to stay on so it can look after its own printhead.
  • Turn on remote printing and Reprint in the device settings. Reprint is what makes batch work bearable.

eufyMake support has shown up for me

Every time I've contacted eufyMake support, they've replied quickly and followed through. That matters a lot more than any spec on this page.

For help from other owners, the eufyMake Discord is a lot more useful than the Facebook groups. People there post the problem and the fix, not just the complaint.

Where it fights you

Placement is the big one

This is the number one frustration I hear from E1 owners, and I hit the same wall myself. The E1 doesn't find its origin with mechanical stops. It finds it with the camera, by reading the corner of the adhesive mat. So wherever that sticker mat sits is where your zero is. Move the mat, and your zero moves with it. Over time the mat loses its tack, jigs start to slide, and you find out only after you have printed a whole tray a couple of millimeters off.

The machine gives you two ways to place a print, and they are good at very different jobs:

Snapshot Camera takes a picture, you drag the art on Great for One item near the center of the bed Full-bleed prints past the edges Not for trays of identical items Zero Point Prints at fixed coordinates from the mat corner Great for Batch jobs in a jig Hitting Reprint on tray after tray The catch only as good as where your jig sits

Ask about alignment on any E1 group and the answer is always "use Zero Point and a jig." That's right, but it leaves out the part that makes it work: the jig has to land in the exact same spot every time, and the stock bed gives you nothing to register it against. That's why I built my own alignment system for the mini bed. It took me two to three months of design work, and I sold it to customers for a good while before I ever made a video claiming it worked.

In my testing I pulled a heart-shaped pet tag out, put it back and reprinted it four times over. You can't see any shift in the design. That's the difference between a toy and a production tool.

From the Samcraft shop
Samcraft Jig Alignment System on the eufyMake E1 mini bed, an edge rail and a corner bracket in light gray positioned for drop-in jig layouts.
Jig Alignment System for the eufyMake E1

Two pieces that clip onto the mini bed and give every Samcraft jig a hard edge to sit against. Drop a jig in, print, pull it out, drop in the next one. It comes with a calibration card and my walkthrough video for dialing in your machine.

Fits the E1 mini bed only, not the standard bed. Made to order in Tennessee.

See the Jig Alignment System

And here's what it lines up. Coasters, bottle stoppers, sports balls, pens, pet tags and more, all built to drop into the same system:

Samcraft car coaster jig on the eufyMake E1 print bed, holding four round white car coasters in circular recesses. Samcraft bottle stopper jig on the eufyMake E1 print bed, holding a row of wood-topped bottle stoppers upright. Samcraft sports ball jig on the bed of a eufyMake E1 UV printer, holding a baseball, a yellow pickleball and a yellow softball in cupped recesses.
Build an E1 Starter Kit: pick four jigs and the accessories drop to half price

If you want to see the whole workflow, jig in, template in eufyMake Studio, batch out, I filmed it start to finish:

Know your working envelope

The spec sheet says the mini bed prints 330 x 90 mm. Using Zero Point, which is how every one of my jigs works, the real usable area on my machine is 333 x 88 mm. That 88 mm front to back is the number that bites. Anything deeper than 88 mm won't print on the mini bed no matter how you turn it, so check your item against it before you promise a customer anything.

Drawn to scale Standard bed 330 x 420 mm objects up to 60 mm tall Mini bed 330 x 90 mm objects up to 80 mm tall 333 x 88 mm usable with Zero Point, my measurement Both beds Print face level within 2 mm 1.5 kg max on the bed 5 mm or more between items 330 mm wide

The height rule matters just as much. UV ink is fired from a fixed height, so every item in a batch needs its top surface at the same level. eufyMake says to keep the print face within 2 mm. In my shop I treat about 3 mm as the absolute edge before the print starts to go soft. A good jig holds the tops level for you, which is half of what a jig is for. If you want to find your own machine's number, my free Z height test does it in an afternoon.

The smell

UV printing smells. That's the chemistry, not a flaw in the E1, same way a laser makes smoke. The E1 ships with an activated carbon filter, and for me it wasn't enough. The smell hangs around the shop even when the machine is idle, and it gave me headaches every day I was out there.

What fixed it was venting the machine outside: a fume extractor in the filter slot, a 4 inch hose, an inline duct fan and a window vent kit. Since then, no headaches. I designed my own fume extractor for the E1 for exactly this, and it takes either a 4 inch hose or an xTool AP2 hose. Whatever you use, if the machine lives in a closed room, plan on getting the air out.

Ink goes to the machine, not just your prints

On a tumbler logo, the software estimated about 0.04 ml of ink. The print itself barely uses anything. Where the ink really goes is priming, cleaning and coming out of standby, which the E1 does to keep its printhead from clogging. If the machine sits, expect a priming cycle of around two and a half minutes before your first job. The practical lesson: an E1 that prints every day costs less per print than one that prints on Saturdays.

Tumblers: skip the stepped ones

With the rotary, the E1 does a nice job on straight and tapered tumblers. It auto-measures the taper with its lasers and prints right on the powder coat. Stepped tumblers are a mixed bag at best. Buy straight or simple tapered blanks. eufyMake's rotary handles tapers up to 13 degrees.

One more tumbler lesson that surprised me: orientation drives print time, not color. My horizontal logo took about seven minutes. The same logo turned 90 degrees took under four, because the printhead has less distance to travel on each pass.

Straight from my notes

The software's time estimate ran short every time I checked it. A job it called five and a half minutes took seven. Price your jobs off what the machine actually took, not what the preview says.

What I'd add on day one

Three things, in this order:

  1. A way to vent the fumes. Filter slot extractor, hose, inline fan, out a window or wall.
  2. A reusable bed mat. The stock adhesive mats wear out, and they are what your zero is measured from. Keep them for alignment and let something else take the overspray.
  3. An alignment system and jigs, if you plan to sell. One-off gifts don't need them. Batches of fifty do.
From the Samcraft shop
Samcraft FatMat fitted to the print bed of a eufyMake E1 UV printer, the black silicone mat filling the tray.
Samcraft FatMat for eufyMake E1

A silicone bed mat I cut to the E1's beds, one for the standard bed and one for the mini bed in the same kit. It takes the overspray so your adhesive mat doesn't, and a lint roller or a little isopropyl alcohol cleans it right back up.

Designed and made in Tennessee

See the E1 FatMat

Should you buy one?

Buy it if

  • You print hard goods: acrylic, wood, metal, ceramic, leather patches, tumblers
  • You want raised texture and photo-quality color on a desktop
  • You value a big template library and a large owner community
  • You'll put in the work to set up a real placement workflow for batches

Think twice if

  • You want to print apparel. The E1 isn't a garment printer.
  • You need production batches tomorrow with no jigs or alignment plan
  • It will live in a closed room with no way to vent it

Weighing it against the xTool O1 Omni? I broke that down in eufyMake E1 vs xTool O1 Omni.

See the eufyMake E1 at eufyMake (affiliate link)

Common questions

Is the eufyMake E1 good for a small business?

Yes, for hard goods, as long as you plan for batch work. Out of the box it's at its best on one item at a time. To run trays of identical products you need Zero Point, a jig, and a way to put that jig in the same place every time.

Why do my E1 prints land in a slightly different spot each time?

The E1 finds its zero point optically, from the corner of the adhesive mat, not from mechanical stops. If the mat or your jig shifts even a little, the print shifts with it. A fixed alignment system on the bed takes that variable out.

What's the difference between Snapshot and Zero Point?

Snapshot takes a camera picture and lets you place art on the item by eye. It's best for a single piece or a full-bleed print. Zero Point prints at fixed coordinates measured from the mat corner, which is what you want for jigs, batches and the Reprint button.

How big an object can the E1 print on?

Per eufyMake, the standard bed prints 330 x 420 mm with objects up to 60 mm tall, and the mini bed prints 330 x 90 mm with objects up to 80 mm tall. On my machine the usable mini bed area with Zero Point is 333 x 88 mm. The rotary takes items 45 to 100 mm in diameter and 80 to 245 mm tall, with a taper of up to 13 degrees.

Does the eufyMake E1 need ventilation?

It has a built-in carbon filter, and eufyMake's ink carries GREENGUARD Gold certification for low emissions. In my shop the resin smell still gave me headaches until I vented the machine outside with an extractor, a 4 inch hose and an inline fan. If yours is in a closed room, plan to vent it.

Can the E1 print on stepped tumblers?

Not reliably. In my experience the results are a mixed bag. Straight tumblers and simple tapers up to 13 degrees work well with the rotary.

Does the E1 use ink when it's not printing?

Yes. Priming, cleaning and coming out of standby use far more ink than a typical small print. A machine that runs regularly wastes less per print than one that sits for days between jobs.

Do Samcraft E1 jigs fit the standard bed?

No. My E1 jigs and the Jig Alignment System are built for the mini bed. That's where Zero Point is most repeatable, and it's the bed most batch work happens on.

More from the Maker Guides

eufyMake E1 vs xTool O1 Omni head-to-head

Free UV printer test kit: nozzles, color, white and registration

Two free tests: Z height range and printing on spheres

Free eufyMake E1 print scale calibration tool

See the eufyMake E1 gear

Watch more of my E1 testing on Samcraft on YouTube, including the full setup walkthrough, UV printing tumblers and venting the fumes.

Sam

Disclosure: eufyMake provided my first E1 in 2025 in exchange for video content. eufyMake links in this post are affiliate links that may earn Samcraft a commission at no extra cost to you. eufyMake has no editorial input or control over Samcraft content. Samcraft designs and sells its own accessories for the E1, including the jigs, alignment system, FatMat and fume extractor mentioned here. Specifications are from eufyMake's published documentation unless marked as my own measurement. Last reviewed September 2026.

Back to blog